You have no idea how much I stressed over drilling out this big beautiful golden pearl.

Jacquelyn contacted me with this pearl conundrum: she had a pearl that came from a necklace (so it was drilled all the way through) but wanted it for a ring. So… could I maybe set a stone or do something not weird with the hole in the top? Being me, I’m all “We should put a diamond in that hole.” So I got to work. I made the wax, adjusted it to size, got it cast, finished it out, set the diamond in the tubing, shaped and prepped the tubing to be set in the pearl, prepped the mounting for the pearl… and then I stopped and sweat for like a week.

I was terribly paranoid about chipping the surface of the pearl when I drilled it out for the diamond stud. I drill pearls all the time and I use special pearl drilling bits, but they are only small holes, like 1/2 millimeter in diameter. This was to be a 2.5mm diameter hole and as far as I know, they don’t make special pearl drill bits this size. Regular twist drills don’t work; they trash the nacre and chip it all to hell. I have tried. One could suggest that I had two chances to set the pearl: once on one side and if that didn’t work, then I could set the failed end down and have a fresh chance. Naturally, that idea sucked because I just couldn’t give back a pearl all wanged up even if the wanged-up part was set down into the ring and invisible. Also, the pearl had a couple of little dits on one end; this end needed to be set down in the ring mounting. So basically I had one chance. GAH!

I decided to treat the pearl like it was a normal setting job and used the tools I use to set diamonds. Bud burr, setting burrs, etc. The trick seemed to be that I had to drill the pearl at an extreme angle to keep it from chipping (I know this because I trashed two other practice pearls figuring it all out). Then once the nacre is opened up, you can drill straight down. It took a steady hand and a lot of patience but when I finally got my nerves together to do the real thing, it worked flawlessly.

I was never so happy to put that ring in the box and tie a little ribbon around it and send it off. Would I do it again? ABSOLUTELY! My god just look at how awesome it is:

Like a jeweled gooseberry. With a big sparkley bead of dew on it. YUM.

I got a recent commission for a matching pair of wedding bands with perhaps a fish theme (the owners had a sweet story about a minnow). I did a couple of sketches of minnows wrapped around a band. Then it came up that the peacock feather was the design theme of their wedding. Maybe we could work that into the ring…

A fish and a feather. Ooh!

[I may not know how to spell "lacy" but I do know my feather anatomy!]

I really had a fun time carving these rings. A while back I sketched a design for a big ol’ peacock ring (peacocktail ring?) but never got around to actually carving it. Maybe I’ll dig it back out now because I love how the feather motif worked on the ring.

I start out evenly: cut waxes, cut out basic shape with file, scratch in design with something scratchy… Then I go to town. I try to keep continuity by carving on both rings, not getting ahead too far on one or the other, but inevitably at some point I lose myself and focus on one ring until I’m essentially finished.

As usual, I carved the first ring (hers) and looked at my rough scratches on the second ring (his) and said to myself: “Oh bother; how can I make this one as good as the first?” This happens every time. And every time the same thing happens.

I carve the second ring… and I like it even better than the first.

Then I feel bad for the first ring.

But after a short time my feelings equalize and I really find in the end that I don’t know which one turned out “best.”

Because they both turned out perfectly.

18K gold custom rose and ginkgo ring. This is a recent custom order I finished for a woman in Japan.

First I sketched a potential design. Once this was okayed, I could start in with the wax carving.

To start with, I hacked off a slice of carving wax the width of the proposed ring. I bored out the inside to the proper ring size, filed the sides parallel, and filed down the top to an even thickness. This step used to take me a ridiculously long time but now I’m pretty good at it and can brute out a general ring shape in no time. I typically carve a thick ring; rings feel better to me when there is some substance to them. I start with 2.5mm thickness generally and whittle down from there. The final ring will usually be around 2.25 thickness.

I measured out my three rose groupings so they would be even and balanced. Then I started to sketch out my design by scratching it onto the wax with a dental tool. I often have to adjust my design once actually laid out onto the wax since it always fits differently than it does on a piece of notebook paper.

Here I’ve bored out the holes between the ginkgo leaves and cut away excess wax. I use a regular twist drill and exacto knife to do this.

Neatening the openwork and starting to shape a little. Once I get the shape right, I start carving contour with a dental tool. I have a number of dental tools but I really only use one, which I’m absurdly dependent upon. I got it from my dentist years ago and sharpened a new, pointier point onto it. I broke one end of it off a few years back and I’ll be severely irritated if I ever break off the remaining end, which has thee perfect angled tip and the perfect amount of springiness and flexibility.

Here I’ve roughed out the shape on the leaves and started to form the roses. I’m going for a lot of movement on this ring, high relief.

The wax carving is almost complete. I go over and over the piece to neaten up edges, clean up my scratch marks, and make sure the continuity is nice between the outside carving to the smooth inside edge of the band. I often use 1200-grit sandpaper in this step, which is pretty much crazy time, but I always thank myself later when I don’t have to sand irritating scratches out of metal.

Once I’m finished with the basic carving, I do the finishing texture and details. Here I’ve done a bit more work on the rose petals and added the ginkgo leaf texture. The wax model is complete.

The glamour shots. Sometimes it’s hard to imagine the ring when it is purple wax… I’ve been experimenting with removing the color, etc. I can’t decide if it really helps though.

I’m still working on getting the lighting just right in the new studio. I took the finished gold photo before I got my diffuser working right. Unfortunately, it’s the only one that really worked and I didn’t get any others of different angles of the ring, showing more of the roses. Oh well.

EDITED: You can see a photo spread of Pheigi & Kiichiro’s amazing Scottish/Japanese/Steampunk style wedding here.